New York Road Signs Test
- 40 road signs
- 20 per round
- 2 of 4 signs needed on the real test
- Misses come back first
-
Road signsSign 1 of 20
Signs with a red circle and a red line through a picture, like this one, mean:
- AThe action shown is allowed with care
- BThe action shown is allowed at night
- CThe action shown is not allowed
- DThe action shown is required ahead
Show answer and explanation
Answer: C. The action shown is not allowed
A red circle with a red line through it means the picture inside shows something you cannot do. The sign may also include words. This one forbids right turns, and the same design is used for no left turn, no U-turn, and other prohibitions, so you can understand them even without reading.
Why not A? The red line means the action is forbidden, not allowed with care.
Why not B? A red circle with a slash means the action is not allowed.
Why not D? It forbids the action shown; it never requires it.
Source: New York State Driver's Manual (MV-21), “Other Regulation Signs,” Chapter 4 · Review this topic
-
Road signsSign 2 of 20
This sign with an arrow means:
- APass on the right
- BTurn right at the next street
- CRight lane exit only
- DKeep right of the divider
Show answer and explanation
Answer: D. Keep right of the divider
The New York Driver's Manual lists Keep Right of Divider among the Road Signs You Must Know for the written test. Where a divider or obstruction splits the road, the arrow points to the side you should drive on, so pass to the right of the divider.
Why not A? The sign does not say anything about passing.
Why not B? The sign marks an obstruction; it does not order a turn.
Why not C? The sign does not mark an exit lane.
Source: New York State Driver's Manual (MV-21), “Road Signs You Must Know,” Road Signs You Must Know · Review this topic
-
Road signsSign 3 of 20
What does this sign mean?
- AOne-way road; enter slowly
- BDo not stop in the intersection
- CDo not enter this road or ramp
- DGo in one direction only
Show answer and explanation
Answer: C. Do not enter this road or ramp
DO NOT ENTER is a red and white regulatory sign. Follow its instruction: do not enter the road or ramp where the sign is posted. It faces drivers who would otherwise be going against traffic. If you see it in front of you, do not drive past it; choose another route instead.
Why not A? The sign forbids entering at all; it does not allow a slow entry.
Why not B? Stopping in an intersection is covered by the DO NOT BLOCK INTERSECTION sign.
Why not D? The sign means do not enter.
Source: New York State Driver's Manual (MV-21), “Road Signs You Must Know,” Road Signs You Must Know · Review this topic
-
Road signsSign 4 of 20
On a street with two lanes going your way, you see this sign before a crosswalk. A person is starting to cross. Where should you stop?
- ARight at the crosswalk edge
- BBack at the yield line
- COnly if they are in your lane
- DAt the middle of the crosswalk
Show answer and explanation
Answer: B. Back at the yield line
This sign is placed before crosswalks on roads with several lanes, usually with a yield line painted 20 to 50 feet before the crosswalk. Stopping back at that line keeps you from blocking other drivers' view of the person crossing, and the person's view of cars coming in the next lane.
Why not A? Stopping at the crosswalk edge can hide the person from drivers in the next lane.
Why not C? You must yield to a person in the crosswalk whichever lane they are in.
Why not D? Stop back at the yield line.
Source: California MUTCD, “Yield Here To Pedestrians Signs and Stop Here For Pedestrians Signs (R1-5 Series),” p. 165 · Review this topic
-
Road signsSign 5 of 20
What does this sign mean?
- ADo not enter the intersection at all
- BDo not stop inside the intersection
- CAlways stop before the intersection
- DStop and wait inside the intersection
Show answer and explanation
Answer: B. Do not stop inside the intersection
DO NOT BLOCK INTERSECTION is a white regulatory sign. It means you must not stop inside the intersection. If traffic is backed up and there is not enough room to get completely across, wait before the intersection until space opens up. When there is room, you may cross normally without stopping.
Why not A? You may cross when there is room to clear the intersection completely.
Why not C? You do not have to stop when there is room on the other side.
Why not D? Do not stop inside the intersection.
Source: DL 600, “White Regulatory Signs,” p. 36 · Review this topic
-
Road signsSign 6 of 20
What does this sign mean?
- ANarrow road ahead
- BWinding road ahead
- CCurve to the right ahead
- DSlippery when wet
Show answer and explanation
Answer: D. Slippery when wet
Diamond-shaped signs warn you of specific road conditions and dangers ahead. This one shows a car with wavy skid marks behind it, which means slippery when wet. The road may be slippery in rain, so slow down. Learning each warning symbol lets you react before you reach the hazard.
Why not A? This sign warns of a slippery road when wet.
Why not B? The winding road ahead sign shows an S-shaped arrow.
Why not C? The curve to the right ahead sign shows a single arrow bending to one side.
Source: DL 600, “Warning Signs,” p. 37 · Review this topic
-
Road signsSign 7 of 20
This yellow diamond sign with a traffic light means:
- AThe signal ahead is broken
- BTraffic signal ahead
- CYou must stop in 500 feet
- DA pedestrian signal is ahead
Show answer and explanation
Answer: B. Traffic signal ahead
The New York Driver's Manual lists Traffic Signal Ahead among the Road Signs You Must Know for the written test. Warning signs are normally yellow and diamond-shaped with black symbols, and they tell you of a hazard or special condition ahead, so be ready to stop at the signal.
Why not A? The sign shows a signal exists; it does not say it is broken.
Why not C? The sign does not give a distance or order a stop.
Why not D? The sign shows a three-light signal for vehicles, not a pedestrian signal.
Source: New York State Driver's Manual (MV-21), “Road Signs You Must Know,” Road Signs You Must Know · Review this topic
-
Road signsSign 8 of 20
What does this sign tell you to do?
- AUse only the right lane ahead
- BDo not change lanes until it is allowed
- CMerge into one lane ahead
- DMerge left when you see it
Show answer and explanation
Answer: B. Do not change lanes until it is allowed
A STAY IN LANE sign is used on roads with several lanes to direct drivers to stay in their lane until conditions allow a lane change. It is usually paired with solid double white lane lines, which also mean no lane changes. Wait until the lines become broken before you move over.
Why not A? It does not pick a lane; it tells you to stay in the one you are in.
Why not C? Lane merges are shown on yellow warning signs.
Why not D? This sign says to stay in lane until the solid line ends.
Source: California MUTCD, “STAY IN LANE Sign (R4-9),” p. 192 · Review this topic
-
Road signsSign 9 of 20
What does this sign mean?
- ATraffic moves only in the arrow's direction
- BThe road is closed in that direction
- CYou must turn the way the arrow points
- DA detour follows the arrow's direction
Show answer and explanation
Answer: A. Traffic moves only in the arrow's direction
A ONE WAY sign is a regulatory sign that shows which way traffic travels on that street. Drive only in the direction of the arrow. It does not tell you to turn and it does not mark a detour. Turning onto the street against the arrow would put you head-on with traffic.
Why not B? Traffic moves only in the arrow's direction.
Why not C? It does not order a turn; it tells you which way traffic on that street flows.
Why not D? The sign is about the direction of traffic on the street, not a detour route.
Source: DL 600, “White Regulatory Signs,” p. 36 · Review this topic
-
Road signsSign 10 of 20
What does this sign mean?
- AA detour goes to the right
- BA detour goes to the left
- CTraffic on the road ahead flows one way
- DThe road turns sharply that way
Show answer and explanation
Answer: D. The road turns sharply that way
This yellow warning sign is a directional arrow. Warning signs alert you to specific road conditions and dangers ahead; this one means the road changes direction sharply in the way the arrow points. Slow down before you reach the turn and follow the road around it.
Why not A? This yellow warning sign marks a sharp change in direction, not a detour.
Why not B? This sign shows the road turns sharply in that direction.
Why not C? One-way streets are marked with a black and white ONE WAY sign.
Source: DL 600, “Warning Signs,” p. 37 · Review this topic
-
Road signsSign 11 of 20
What does this sign mean?
- ACrossroad ahead
- BT intersection ahead
- CTwo-way traffic
- DWinding road ahead
Show answer and explanation
Answer: B. T intersection ahead
Diamond-shaped signs warn you of specific road conditions and dangers ahead. This one shows a T shape, which means t intersection ahead. Your road ends at a crossing road, so be ready to turn. Learning each warning symbol lets you react before you reach the hazard.
Why not A? The crossroad ahead sign shows a plus sign.
Why not C? The two-way traffic sign shows two arrows pointing in opposite directions.
Why not D? This sign shows a T intersection ahead.
Source: DL 600, “Warning Signs,” p. 37 · Review this topic
-
Road signsSign 12 of 20
What does this sign mean?
- ANo U-turn
- BRight turn only
- CNo left turn
- DRoad curves sharply ahead
Show answer and explanation
Answer: A. No U-turn
A red circle with a red line through it means you cannot do what the picture inside shows. Here the picture is the arrow for this movement, so the sign means no u-turn. You will often see these signs at intersections where the movement is unsafe. Obey them even if the turn looks clear.
Why not B? This sign means no U-turn.
Why not C? The arrow on this sign doubles back; a no-left-turn arrow bends left only.
Why not D? Curve warnings are yellow diamonds, not red circles.
Source: New York State Driver's Manual (MV-21), “U-Turns,” Chapter 5 · Review this topic
-
Road signsSign 13 of 20
What does this sign mean?
- ACurve to the right ahead
- BT intersection ahead
- CWinding road ahead
- DSlippery when wet
Show answer and explanation
Answer: C. Winding road ahead
Diamond-shaped signs warn you of specific road conditions and dangers ahead. This one shows an S-shaped arrow, which means winding road ahead. A series of curves is ahead, so slow down. Learning each warning symbol lets you react before you reach the hazard.
Why not A? The curve to the right ahead sign shows a single arrow bending to one side.
Why not B? This sign shows a winding road.
Why not D? The slippery when wet sign shows a car with wavy skid marks behind it.
Source: DL 600, “Warning Signs,” p. 37 · Review this topic
-
Road signsSign 14 of 20
This yellow diamond sign means:
- AThe left lane ends ahead
- BMerging traffic enters from the left
- CRight lane ends - stay to the left
- DThe road ahead divides
Show answer and explanation
Answer: C. Right lane ends - stay to the left
The New York Driver's Manual lists the sign Right lane ends - stay to the left among the Road Signs You Must Know. Warning signs are normally yellow diamonds with black symbols, and this one tells you the right lane is ending, so check for traffic and move left in time.
Why not A? The sign shows the right lane ending, not the left.
Why not B? A merging-traffic sign shows another road joining, not a lane ending.
Why not D? A divided highway sign shows the road splitting.
Source: New York State Driver's Manual (MV-21), “Road Signs You Must Know,” Road Signs You Must Know · Review this topic
-
Road signsSign 15 of 20
This yellow diamond sign warns that:
- AThe divided highway ends
- BThe road ahead is one-way
- CThe highway is closed
- DA divided highway begins
Show answer and explanation
Answer: A. The divided highway ends
The New York Driver's Manual lists Divided Highway Ends among the Road Signs You Must Know. Warning signs are normally yellow diamonds with black symbols and mark a hazard or special condition ahead, so expect oncoming traffic on the same roadway once the divider ends.
Why not B? A one-way sign shows arrows in a single direction.
Why not C? The sign does not say the highway is closed.
Why not D? The sign shows the divided highway ending, not starting.
Source: New York State Driver's Manual (MV-21), “Road Signs You Must Know,” Road Signs You Must Know · Review this topic
-
Road signsSign 16 of 20
You see this sign at a ramp leaving a long, steep downhill road. What does it mean?
- AAny vehicle may park there
- BTrucks may rest on the ramp
- CSlow vehicles may pull off there
- DOnly runaway vehicles may use it
Show answer and explanation
Answer: D. Only runaway vehicles may use it
This sign is placed near the entrance to a truck escape ramp, also called a runaway truck ramp. The ramp is for vehicles that have lost their brakes on a steep grade. The sign discourages other drivers from entering it, and you should never stop in the path of a runaway truck.
Why not A? The ramp is only for runaway vehicles.
Why not B? The ramp is an escape route, not a rest stop.
Why not C? Pulling onto the ramp could block a truck whose brakes have failed.
Source: California MUTCD, “RUNAWAY VEHICLES ONLY Sign (R4-10),” p. 192 · Review this topic
-
Road signsSign 17 of 20
You see this sign after a stretch of two-lane road where passing was not allowed. What does it mean?
- AThe no-passing zone has ended
- BA no-passing zone begins here
- CA passing lane ends
- DYou may now pass on the right
Show answer and explanation
Answer: A. The no-passing zone has ended
A PASS WITH CARE sign is placed at the far end of a no-passing zone that began with a DO NOT PASS sign. It tells you passing is allowed again. You still must pass only when you can see far enough ahead and have enough room to return to your lane safely.
Why not B? The start of a no-passing zone is marked with a DO NOT PASS sign.
Why not C? This sign means the no-passing zone has ended.
Why not D? It ends the no-passing zone; passing is still done on the left.
Source: California MUTCD, “PASS WITH CARE Sign (R4-2),” p. 190 · Review this topic
-
Road signsSign 18 of 20
What must you do as you approach this sign?
- ADecrease speed and be prepared to stop and yield the right-of-way
- BStop fully every time
- CMaintain speed if no one is visible
- DPull to the side and wait
Show answer and explanation
Answer: A. Decrease speed and be prepared to stop and yield the right-of-way
The New York Driver's Manual says to decrease speed as you reach the intersection, prepare to stop and yield the right-of-way to vehicles and pedestrians in or heading toward the intersection. You must come to a full stop at a Yield sign if traffic conditions require it.
Why not B? A full stop is required only if conditions require it.
Why not C? You must slow down even when it looks clear, because traffic may be hidden.
Why not D? You do not need to leave the roadway at a yield sign.
Source: New York State Driver's Manual (MV-21), “Yield Sign,” Chapter 4 · Review this topic
-
Road signsSign 19 of 20
You are stopped at a red light and see this sign. What is true?
- AYou may turn right after a full stop
- BYou may turn left from any lane
- CYou may turn if no pedestrians are present
- DYou must wait for a green light before turning
Show answer and explanation
Answer: D. You must wait for a green light before turning
The New York Driver's Manual says you cannot make a turn at a red light if there is a NO TURN ON RED sign posted. Even though a right turn on red is normally allowed after a full stop, this sign overrides it, so wait for a green light or green arrow.
Why not A? The sign removes the usual right turn on red permission.
Why not B? Left turns on red are limited and this sign bans turning on red.
Why not C? Empty crosswalks do not change what the sign requires.
Source: New York State Driver's Manual (MV-21), “Traffic Lights,” Chapter 4 · Review this topic
-
Road signsSign 20 of 20
Traffic is backed up and your exit is close. You see this sign. What may you do?
- ADrive on the shoulder to reach the exit
- BUse the shoulder if you signal first
- CStay in a lane and wait
- DPass traffic on the shoulder
Show answer and explanation
Answer: C. Stay in a lane and wait
The DO NOT DRIVE ON SHOULDER sign tells drivers that using the shoulder as a travel lane is prohibited. The shoulder is kept clear for emergencies and stopped vehicles. Stay in your lane, even in slow traffic, and leave the shoulder for emergency vehicles and drivers who need to pull over.
Why not A? The sign forbids using the shoulder as a travel lane, even for a short way.
Why not B? Signaling does not make driving on the shoulder legal.
Why not D? Stay in a lane and wait.
Source: California MUTCD, “DO NOT DRIVE ON SHOULDER Sign (R4-17) and DO NOT PASS ON SHOULDER,” p. 193 · Review this topic
Study first
Learn the New York road signs
The manual says to know its signs: you'll be asked about them on your written test, and you must get at least 2 of the 4 sign questions right.
Signs test FAQ
New York road signs test FAQ
What's on this road signs test?
Questions on the signs in the New York State Driver's Manual, such as stop, yield, do not enter, no left turn and no U-turn, plus warning signs like merge, right lane ends and traffic signal ahead.
How many questions are on this signs test?
17 questions per round, one for each manual sign we cover. Signs you miss come back in later rounds until you get them right.
Is this the same as the DMV test?
No. This is practice. On the real test, 4 of the 20 questions are about road signs and you must get at least 2 of them right.
What should I do after I pass the signs test?
Move on to the permit practice test, then take the full permit exam until you pass twice in a row.
Checked against the New York State Driver's Manual.
Written from the official handbook and dmv.ny.gov. Checked line by line against the official handbook and state law.
Last checked Oct 2026